What Should You Consider Before Ordering a Bespoke Shower Screen?
Ordering a bespoke shower screen is a one-shot decision. Toughened glass is cut, shaped and drilled before it is heated and rapidly cooled, which means it cannot be trimmed, drilled or altered afterwards. A wrong measurement or an overlooked hole position means a replacement panel, not a quick fix on site.
This guide walks through the decisions in the order you will meet them: choosing the right glass thickness, measuring accurately, selecting hardware and finishes, planning around your bathroom’s layout, and running a final check before you order. By the end, you will know what to settle first and what to confirm with your supplier.
Which Glass Thickness Suits Your Shower Enclosure?
For most domestic shower screens and doors, the usual choice is 8 mm or 10 mm toughened glass, depending on the design and the hardware supporting it. Toughened glass is safety glass: it is heat treated so that it is significantly stronger than ordinary annealed glass, and if it breaks it crumbles into small blunt pieces rather than sharp shards.
Thickness is not a free choice, and no single thickness suits every enclosure. The right option depends on the size of the panel, how it is fixed and the hinges or channels carrying it. For example, a compact fixed panel held in a channel places different demands on the glass than a tall, frameless door hanging from two hinges.
It also helps to clear up a common misconception. Thickness guidance for shower glazing does not carry over to other glass applications. Frameless balustrades and Juliet balconies follow completely different requirements, so never use balustrade advice to size a shower screen, or the other way round.
When you order a toughened glass panel, look for the BSI Kitemark. It shows the glass has been manufactured to a recognised British safety standard, and it is a sensible quality check when comparing suppliers online.
How to Measure for a Made-to-Measure Screen
The golden rule is to measure only after the tiling, the shower tray and the finished flooring are fully installed. Measuring earlier is one of the most common causes of panels that do not fit, because tiles and trays change the final dimensions.
Walls are rarely perfectly square, and floors are rarely perfectly level. Work through these steps to capture the real shape of your space:
- Measure width at several heights. Take readings at the bottom, middle and top of the opening, because walls often lean slightly out of vertical.
- Measure height at each end. A floor that slopes towards the drain can make one side of the screen taller than the other.
- Check the walls with a spirit level. Note any lean so you can discuss it with your supplier.
- Allow for clearances. Hinges, channels and seals all need space, and the glass size must reflect them.
- Record every measurement in millimetres. Write them down on a simple sketch to avoid confusion later.
Because glass must be made to its final dimensions before toughening, there is no scope to trim a panel that arrives slightly oversized. Where your readings differ noticeably from one height to the next, ask the supplier how they recommend specifying the panel. Measuring twice and having someone check your figures is time well spent.
Choosing Hardware, Finishes and Glass Options
Once the size is settled, hardware becomes the next major decision, because the hinges, clamps and channels determine how the glass is supported and how the screen looks. A shower door needs hinges capable of carrying the weight of the glass and allowing the opening movement you want. As general guidance, two hinges are common for shower doors, with three recommended for doors taller than 2 metres. Treat that as a starting point rather than a rule, since the number and type of hinges must suit the specific panel and the hardware maker’s load limits.
Matching Fittings to Your Glass
Fittings are not interchangeable simply because they look alike. Each component has a stated glass thickness range and load capacity, so check these against your chosen panel. Browsing a range of glass fittings and hinges is a useful way to see what is available, from clamps and hinges to handles and sliding door hardware.
Typical hardware finishes include polished chrome, brushed chrome, stainless steel, brass, brushed brass, brushed copper and matt black. Choosing a finish that matches your taps, shower head and towel rail gives a coordinated result.
Glass Types and Edge Finishes
You can also customise the glass itself. Common options include clear, extra-clear low-iron, grey tinted, bronze tinted and satin finishes. Clear glass suits most bathrooms, low-iron glass reduces the slight green tint seen at the edge of standard clear glass, and satin glass adds privacy. Specify your edge treatment at the same time, with polished edges being a common choice for exposed edges.
Planning Around Layout, Waterproofing and Installation
A screen must be fixed to a structure strong enough to support it. Solid masonry walls generally provide secure fixing points, whereas stud walls may need extra reinforcement to carry the load safely. If you are unsure what your walls can take, ask a qualified tradesperson to assess them before you order.
On layout, think about door swing. A hinged door needs clear space to open without hitting a toilet, vanity unit or radiator. If space is tight, a fixed panel or a sliding option may be a better fit. For a screen over a bath, consider whether a fixed or hinged glass bath screen suits your bathroom better.
Water containment deserves realistic expectations. Seals, correct alignment and well-applied sealant all help, but no frameless design can be guaranteed completely watertight. Small amounts of splashing around door edges can still occur, so plan your tray position and screen width with that in mind.
During installation, protect the glass edges. Toughened glass can shatter if an edge strikes a hard surface such as concrete, so use packing materials, gaskets and protective supports to prevent contact between glass and hard surfaces or metal fittings. Align panels with a spirit level, fix them in the sequence the hardware maker specifies and allow sealants to cure fully before using the shower.
What to Check Before You Place Your Order
Before you commit, run through a final checklist. It brings together everything covered above and catches the errors that are hardest to reverse.
- Measurements: taken after tiling and flooring, at several heights, with clearances accounted for.
- Glass type and thickness: suited to your panel size, design and chosen hardware.
- Finish and edges: glass tint or satin finish chosen, with edge treatment specified.
- Holes and cut-outs: positions confirmed against your hinges, handles and fittings, since drilling is impossible after toughening.
- Hardware compatibility: hinges, clamps and channels matched to the glass thickness and weight.
- Wall structure: confirmed as strong enough to take the screen, with reinforcement planned if needed.
- Safety marking: BSI Kitemark confirmed on the glass supplied.
If any figure or specification is uncertain, speak to the supplier before ordering rather than guessing. A short conversation is far cheaper than remaking a panel.
Explore Bespoke Glass Shower Screens with Express Glass Warehouse
Express Glass Warehouse supplies bespoke, UK-made toughened glass shower screens and bath screens, so you can order panels cut to the dimensions you have measured. A few points worth knowing as you plan:
- Glass options include extra-clear low-iron, clear, grey tinted, bronze tinted and satin toughened glass.
- Bath screens are made from 8 mm clear toughened safety glass with polished edges as standard, with bespoke sizes available on request.
- Hinges, clamps and other hardware are available separately in a range of finishes.
Ready to start your project? Browse the full range of glass shower screens, or get in touch to enquire about bespoke dimensions for your bathroom.




