Can You Replace a Shower Screen Without Replacing the Shower Tray?
Yes, you can replace a shower screen without replacing the shower tray, provided the tray is sound, watertight and still level. A new toughened glass screen only needs a stable, undamaged base and walls that can take the fixings. Most replacements involve careful measuring, a made-to-measure panel and compatible hardware.
The result depends on the tray’s condition, how well the old screen’s fixings can be reused or patched, and whether the new design suits the existing layout. The questions below cover how to check your tray, measure correctly, choose the right glass and install it.
How can you tell if your shower tray is fit to keep?
A shower tray is fit to keep if it is free from cracks, does not flex underfoot, drains properly and shows no signs of leaking. If the tray passes these checks, you can usually replace only the screen and leave the tray in place.
Check the following before ordering new glass:
- Cracks and chips: Look for hairline cracks, especially around the waste and along the upper edges where the screen sits.
- Movement: Press down on the tray. Any flex, creaking or movement suggests poor support underneath.
- Water damage: Soft or discoloured flooring, damp patches on adjoining walls or ceilings below can point to a leak at the tray.
- Level: Use a spirit level across the tray and along the edge. A tray that slopes the wrong way can undermine a new screen’s alignment and seal.
- Sealant: Failed or blackened silicone around the tray perimeter is often a cosmetic issue, but it can hide gaps worth investigating.
If the tray is cracked, unstable or leaking, replace it first. Fitting a new screen onto a failing base wastes money and can leave the glass unevenly supported.
How do you measure for a replacement shower screen?
Measure the opening in several places after the old screen has been removed and the tray, tiles and walls are in their final state. Record the width at the top, middle and bottom, and the height at each side, then use the smallest figures as a starting point for allowances.
Because toughened glass cannot be cut, drilled or reshaped after toughening, every dimension must be right before manufacture. Follow these steps:
- Remove the old screen, frame and any leftover sealant so you can measure the bare opening.
- Measure the width at three heights (low, middle and high), as walls are rarely perfectly vertical or parallel.
- Measure the height from the tray surface to your intended top edge on both sides of the opening.
- Check the tray for level and note any variation along its length.
- Allow for the clearances needed by hinges, channels and seals, which depend on the hardware you choose.
- Record the position of any door handle, hinge or cut-out you need, since these are made during processing.
Measure twice and double-check against the hardware’s specification. If the walls are noticeably out of plumb or the tray is uneven, consider a professional site survey before you order.
Can a new screen fit an old tray’s profile?
Often yes, but the new screen must be made to suit the tray’s actual shape, upstand and fixing area. A made-to-measure panel can be sized to the tray’s footprint, though old fixing holes, channel positions and an irregular tray edge may need to be addressed first.
Consider these points:
- Tray upstand: The glass or its bottom channel needs a flat, stable surface to sit on. A narrow or heavily curved upstand can limit your options.
- Old fixing marks: Holes in tiles or tray edges from the previous screen may be covered by new channels, or filled and sealed.
- Frameless versus framed: Frameless designs rely on precise glass dimensions and good fixings, while framed systems tolerate slightly more variation.
- Shape: Quadrant, offset or corner trays call for bespoke panels, often cut to specific sizes and angles.
Existing trays vary a great deal, so a new screen is best designed around your measurements rather than the old one’s dimensions. If the old screen was a standard size that no longer suits, a bespoke panel is usually the better route.
What glass thickness and type should replace it?
For most domestic shower screens, 8 mm or 10 mm toughened safety glass is the usual choice, depending on the design and supporting hardware. Toughened glass breaks into small fragments rather than sharp shards, which is why it is used in bathrooms.
The right thickness depends on several factors:
- Panel size: Larger or taller panels generally call for thicker glass.
- Design: Frameless screens carry their own weight and rely on the glass and fittings, so hardware compatibility matters.
- Doors versus fixed panels: Hinged doors need hinges rated for the glass weight, with general guidance suggesting two hinges, and three for doors over 2 metres. Always check the hardware maker’s load limits.
- Finish: Options include clear, extra-clear low-iron, tinted and satin glass, which affect privacy and appearance.
Choose fittings to match your glass thickness, and review our guide to toughened glass specifications for background on how the material is made. If your screen has unusual dimensions or large panels, ask the supplier to confirm that the glass and hardware combination suits your design.
What are the steps to swap the screen yourself?
Swapping a shower screen involves removing the old unit, preparing the surfaces, aligning and fixing the new glass, then sealing and curing. Frameless glass is heavy and unforgiving, so work with a second person and take your time.
- Remove the old screen: Cut through old sealant, support the glass or frame, and unscrew fixings. Wear gloves and eye protection.
- Prepare the surfaces: Clean off residue, fill unused holes and check that the tray and walls are dry and sound.
- Check the support: Fixings need a solid structure. Stud walls may need extra reinforcement behind the fixing points.
- Protect the glass edges: Never rest toughened glass directly on a hard surface such as tile, concrete or metal. Use packers, gaskets or isolators, as impact to an edge can cause breakage.
- Position and align: Use a spirit level and secure the panels in the sequence set out for your hardware.
- Seal and cure: Apply sealant as directed, then leave it to cure for the full time stated by the manufacturer before using the shower.
No frameless screen can be guaranteed completely watertight, so good alignment, quality seals and sensible positioning of the screen all help to reduce splashing. If your walls are weak or uneven, or the glass is very large, a qualified fitter should assess the job.
Where can you order shower glass cut to size?
You can order shower glass cut to size from a specialist glass processor that makes toughened panels to your measurements. Look for a supplier offering made-to-measure sizing, polished edges, clear thickness guidance and suitable fittings in one place.
When comparing suppliers, check that they can provide:
- Toughened safety glass in the thickness suited to your design
- Bespoke dimensions, cut-outs and drilled holes created before toughening
- Compatible hinges, clamps and seals, such as those found among glass fittings and accessories
- Clear lead times and delivery information
For a screen over a bath rather than a tray, look at glass bath screens, which are designed for a different fixing arrangement.
Explore Bespoke Glass Shower Screens with Express Glass Warehouse
Once your tray checks out and your measurements are confirmed, the next step is choosing a screen that suits your layout. Express Glass Warehouse supplies bespoke, UK-made toughened glass panels for a range of shower configurations, including frameless screens and shower doors.
- Glass choices include extra-clear low-iron, clear, grey tinted, bronze tinted and satin toughened glass.
- Bespoke sizes are available on request to suit your tray and opening.
- Matching hardware is available among the glass fittings range, so hinges and seals can be selected alongside your glass.
Browse the full glass shower screens collection or get in touch to discuss bespoke dimensions for your project.




