How Do You Measure for a Bespoke Loft Shower Screen?
Measuring for a bespoke loft shower screen is harder than measuring for a standard bathroom. Sloping ceilings, uneven walls and tight eaves mean a single width and height rarely describe the opening. Because toughened glass cannot be cut, drilled or reshaped after toughening, every dimension has to be right before you order.
This guide walks you through measuring an attic shower opening, recording the ceiling angle, making a template for angled edges and checking everything before you order a made-to-measure shower screen in the UK. Work through the steps in order and you will end up with a dimension sheet a glass supplier can use with confidence.
Gather the tools for accurate measuring
Start by collecting the right equipment, because small errors in a loft space quickly add up. Measure only once the tiles, shower tray and finished flooring are installed, as measuring earlier can give you the wrong panel dimensions.
- A steel tape measure (avoid fabric tapes, which stretch)
- A long spirit level, ideally 1 metre or more
- A plumb line or laser level
- A pencil and masking tape
- A digital angle finder or protractor
- Hardboard or MDF offcuts, plus a hot glue gun or screws, for templating
- A notepad or phone to record every figure
Before you measure, decide where the screen will sit and which fittings it will use, such as channels, brackets or hinges. Their clearances affect the final glass size. You can browse compatible glass fittings to see how much space each type needs. Once your tools and fittings are sorted, you can start on the opening itself.
Measure the opening width at several heights
Take the width at multiple points, because loft walls are rarely perfectly vertical or parallel. A single measurement can hide a variation of several millimetres that stops a rigid glass panel from fitting.
- Mark three or four heights on the wall, for example at 100 mm, 600 mm, 1,200 mm and at the highest usable point beneath the slope.
- Measure the opening width at each mark, from finished surface to finished surface.
- Repeat each measurement and note any difference between readings.
- Hold the spirit level or plumb line against each wall to check it is vertical, and record any lean.
- Check the shower tray or floor level along its length for dips or slopes.
Write down every figure rather than averaging them. If the widths differ, tell your supplier, as the glass may need to be sized to the narrowest point with allowance for sealing or channels. You should now have a set of width readings and a clear picture of how true the walls are. Next, deal with the feature that makes a loft different: the ceiling.
Record the sloping ceiling height and angle
Capture the height at several points along the slope and the angle of the ceiling, since these define the top edge of an angled shower screen. A sloping ceiling shower screen only fits well if the glass follows the roofline accurately.
- Measure the vertical height from the shower tray or floor to the ceiling at the front edge of the screen position.
- Measure the height again at 300 mm or 500 mm intervals along the screen line, moving towards the low end of the slope.
- Place the angle finder against the ceiling and record the pitch in degrees.
- Note the lowest point where the glass will meet the ceiling or an eaves wall.
- Mark each height on the wall with masking tape so you can check them again later.
Be aware that loft ceilings often have plasterboard, boxing or insulation that is not perfectly straight. Measure to the finished surface, not the rafters. Confirm your readings by joining the taped marks with a straight edge. The line should match the visible slope of the ceiling. With heights and angle recorded, you are ready to turn them into a shape the glass can follow.
Create a template for angled glass cut-outs
Build a physical template when the glass needs an angled top edge or any non-rectangular shape. Taking a template is the most reliable way to reproduce an awkward slope, and it mirrors the approach used for irregular splashback shapes.
Build the template
- Cut a piece of hardboard or MDF slightly smaller than the opening, leaving a small gap for installation clearance.
- Hold it in the screen position and mark the ceiling line directly onto the board.
- Trim along the mark, then offer the board up again and adjust until it follows the slope closely.
- Mark the position of any hinges, handles or fixings you plan to use.
Allow for clearances
Do not make the template an exact fit. Leave a sensible gap at the sloping edge for movement and sealing, and allow for the clearances your chosen hardware needs. Label the template clearly with the top, bottom, inside and outside faces.
When you hold the finished template in place, it should sit level and follow the ceiling line without forcing. If it does not, trim and retest before moving on, because any template error will be copied into the glass.
Choose glass thickness, finish and fittings
Select the glass specification once your dimensions are known, as thickness and hardware depend on panel size and design. Shower glazing is generally specified in 8 mm or 10 mm toughened glass, subject to the design and the supporting hardware. The right choice for your screen depends on its dimensions, fixing method and configuration, so confirm it rather than assuming.
Consider these points when deciding:
- Fixed or hinged: A fixed panel is secured with channels, brackets or other compatible fittings, and a larger panel may need a tie bar or stabilising support. A door needs hinges rated for the glass weight.
- Finish: Clear, extra-clear low-iron, tinted and satin finishes are available for shower glazing, and satin options add privacy in an open loft layout.
- Edges and holes: Polished edges, drilled holes and notches must be specified before toughening.
- Supporting structure: Stud walls and sloping timber framing may need extra reinforcement to hold the fixings.
Look at the range of glass shower screens to compare configurations, and read about the properties of toughened glass if you want to understand why it is the standard safety choice for showers. If you are placing a screen beside a bath, hinged and fixed options are also covered in the glass bath screens range. Where you are unsure about thickness or structural suitability, consult a specialist before ordering. Once your specification is chosen, it is time to double-check everything.
Check measurements before ordering cut-to-size glass
Verify every figure before you place an order, because toughened glass is made to its final size and cannot be adjusted afterwards. A quick review now costs far less than a rejected panel.
- Re-measure each width and height reading, and confirm they match your notes.
- Compare the template against the opening one more time.
- Check that clearances for seals, channels and hinges are included in the final dimensions.
- Confirm the position of any holes or notches relative to a fixed reference point, such as the corner of the tray.
- Ask a second person to check your sheet for transposed digits or unit mistakes.
Record whether each dimension is a finished opening size or a glass size, and state the glass type, thickness, finish and edge treatment on your order. If any measurement seems uncertain, or the wall condition is unusual, speak to the supplier before ordering rather than guessing. For complex installations, particularly those involving unsupported stud walls or very low ceilings, consider having a qualified fitter assess the structure.
When your sheet is complete and consistent, you can order a toughened glass shower screen cut to size with confidence.
Explore Bespoke Glass Shower Screens with Express Glass Warehouse
With accurate measurements and a template in hand, you are well placed to order a screen that suits your loft shower. Express Glass Warehouse supplies bespoke toughened glass for a range of shower configurations, so you can match the glass to your layout.
- Frameless shower screens, shower doors and bath screens in bespoke sizes
- Glass types including extra-clear low-iron, clear, tinted and satin toughened glass
- A range of fittings and accessories to go with your chosen screen
Browse the glass shower screen collection to compare options, or enquire about bespoke dimensions if your sloping ceiling needs a custom shape.




