How Do You Measure a Shower Screen for an Uneven Wall?
Measuring for a shower screen is straightforward when your walls are square. When they lean, bow or taper, a single tape measure reading can leave you with a toughened glass panel that will not fit. This guide shows you how to measure a shower screen for an uneven wall so you can order made-to-measure shower glass with confidence.
The stakes are higher than with most home projects. Toughened glass cannot be cut, drilled or reshaped once it has been through the toughening process, so the dimensions you supply are the dimensions you get. Follow the steps below and you will finish with a set of reliable measurements and a clear glass size.
Gather the tools for accurate shower measurements
Prepare your equipment before you touch a wall, because accurate readings depend on the right tools. Measure only after tiling, the shower tray and any finished flooring are complete. Measuring earlier is one of the most common causes of incorrect panel sizes, since tiles and trays change the finished dimensions.
- A steel tape measure (a rigid, locking tape is easier to hold steady than a soft one)
- A 1.2 m spirit level, or longer if you have one
- A plumb line or laser level for checking vertical alignment
- A pencil and masking tape for marking measurement points
- A notebook or phone to log every reading against its position
- Hardboard or MDF offcuts if you plan to make a template
Clear the shower area so you can reach every wall and the tray edge. With your tools ready, you can start by finding out how far your walls are from true vertical.
Check how far your walls are out of plumb
Establish how much each wall leans, because this tells you whether a standard rectangular panel will work. A wall that is out of plumb is not perfectly vertical, and the error often grows with height. A wall that looks fine at waist level can be several millimetres out by the top of the screen.
- Hold the spirit level vertically against the wall where the glass will sit, at the lowest point.
- Note whether the bubble sits centred. If not, measure the gap between the level and the wall at the top or bottom.
- Repeat at mid-height and at the full height of your intended screen.
- Use a plumb line hung from the top of the planned screen position as a second check. Measure the distance from the line to the wall at the bottom.
- Record each result and mark which direction the wall leans.
You should now know whether the wall leans in, leans out or stays roughly true. If readings differ by only a few millimetres, a standard approach with a small gap allowance may work. If the difference is larger, or it varies unevenly along the wall, a physical template is worth making. A made-to-measure glass shower screen can be specified to suit unusual dimensions, but only if your measurements are accurate.
Take width and height readings at three points
Measure width at the top, middle and bottom, and height at the left, centre and right. Three readings per dimension reveal any taper or bow that a single measurement would hide. Walls rarely run parallel, so a screen that fits at the base can jam at the top.
Measure the width
- Mark three horizontal lines with masking tape: near the bottom, at mid-height and near the top of the planned screen.
- Measure the opening between the fixing points along each line.
- Write down each number clearly, labelled top, middle and bottom.
Measure the height
- Measure from the finished tray or floor level to the planned top edge at the left side, the centre and the right side.
- Check the tray or floor with a spirit level, because a sloping floor changes the height along the base of the glass.
- Log each reading with its position.
Compare your three width readings and three height readings. If they match within a millimetre or two, the opening is close to square. If they differ noticeably, you have a tapered or uneven opening. Allow for clearances needed by hinges, channels and seals as well as the wall variation.
Work out the glass size and gap allowance
Choose your glass dimensions from the smallest relevant reading, then deduct a sensible gap for fixings and seals. Order to the tightest point so the panel can always be installed, and let seals or sealant cover the larger gaps elsewhere.
As a working rule, take the narrowest width you measured and subtract an allowance for the fitting type. Channels, brackets and seals each need their own clearance, so check the hardware you plan to use. Different fixings take up different amounts of room, which is why it helps to decide on your shower screen fittings and hardware before finalising the glass size. If your screen includes a hinged door, the hinges and opening movement also need clearance.
Avoid specifying a very tight fit. Leaving no tolerance between the glass and surrounding surfaces makes installation difficult and risks edge contact, which can damage toughened glass. Because the panel must be made to its final size before toughening, any holes, notches or cut-outs also need to be specified at the ordering stage. Most homeowners use toughened glass for shower screens, generally in 8 mm or 10 mm thickness depending on the design and supporting hardware.
You should finish this step with a final width and height for each panel, plus a note of the gap you have allowed on each side.
Double-check measurements before ordering glass
Verify every figure at least twice, ideally on a different day. A fresh look often catches transposed digits or a reading taken from the wrong point. Because toughened glass cannot be altered after manufacture, this check is your last opportunity to correct an error cheaply.
- Re-measure all three widths and three heights and compare them with your notes.
- Confirm that your measurements were taken after tiling and the tray were fully installed.
- Check your plumb readings again at one point to confirm nothing has shifted.
- Confirm the position and clearance of any hinges, channels, seals or handles.
- Ask a second person to read your notes back to you against the wall.
If your walls are significantly out of plumb or irregular, make a template from hardboard or MDF cut to fit the opening. A template captures the real shape in a way that numbers alone cannot, and it gives the manufacturer an exact reference. Where any dimension or system requirement is uncertain, check with the supplier before you place your order rather than guessing.
Fix common uneven wall measuring mistakes
Most measuring errors on uneven walls fall into a handful of predictable patterns. Knowing them lets you correct course before the glass is made.
- Measuring only once. A single reading hides taper. Always take three points for each dimension.
- Measuring before tiling or fitting the tray. Finished surfaces change the dimensions. Wait until they are complete.
- Ignoring the floor level. A sloping tray or floor alters the height along the glass base. Check it with a level.
- Using the widest reading. Order to the narrowest point, otherwise the panel may not fit at the tightest part of the opening.
- Forgetting hardware clearance. Hinges, channels and seals all take space, so include them in your calculation.
- Expecting a perfect seal. On uneven walls, gaps are normal and a frameless screen cannot be guaranteed completely watertight. Seals and sealant reduce leakage, but careful positioning of the screen and a well-fitted tray edge also matter.
Uneven walls can also affect how securely a screen is fixed. Stud walls may need extra reinforcement to provide adequate fixing strength, so if you are unsure about the structure behind your tiles, seek a professional assessment before installation. Fixing into a poorly supported wall is a safety issue as well as a fitting problem.
Explore Bespoke Glass Shower Screens with Express Glass Warehouse
Once you have reliable measurements, the next step is turning them into a screen that fits. Express Glass Warehouse supplies bespoke, UK-made toughened glass panels for a range of shower and bath configurations, so you can order to the dimensions you have worked out.
- Bespoke sizes for frameless shower screens, shower doors and bath screens, including sliding or hinged designs
- Glass choices including extra-clear low-iron, clear, grey-tinted, bronze-tinted and satin toughened glass
- Compatible fittings and accessories to match your chosen screen
Browse the full glass shower screens collection to see the options, or look at the glass bath screens range if you are fitting over a bath. If you are unsure about your dimensions, get in touch before ordering so your measurements can be checked.




