How Are Glass Balustrades Fixed to Concrete?

Glass balustrades are fixed to concrete in one of three main ways: a base channel (shoe) bolted to the slab, individual spigots fixed to the slab surface, or core-drilled spigots set into holes drilled into the concrete. Each uses mechanical anchors, chemical anchors or grout to transfer the load from the glass into the structure. This guide walks you through choosing a method, preparing the slab, installing the fixings and setting the glass, so you know what a sound installation involves.
Glass balustrades are safety-critical. The fixings, the concrete and the glass specification all need to work together, so treat this as a guide to understanding the process and speaking confidently with your installer or structural engineer, not a substitute for professional design where load or compliance is in question.

Choose the right concrete fixing method

Start by deciding how the glass will meet the slab, because every later step depends on this choice. The three common options are:

  • Base channel (shoe) systems: a continuous aluminium or stainless steel channel is anchored to the top of the slab and the glass sits inside it. This gives a clean, continuous line and spreads the load along the full length of the run.
  • Surface-fixed spigots: individual stainless steel spigots are bolted to the top of the slab or fixed to its face, with each glass panel clamped between them. This leaves visible gaps between fixings and suits panels of a set width.
  • Core-drilled spigots: spigots are set into holes drilled into the concrete and fixed with grout or resin. These can be used where there is not enough slab top or edge to bolt onto, but they need adequate slab depth and edge distance.

Your choice depends on the slab edge, the available depth, whether the area is indoors or outdoors, and the look you want. Fixing to the top of the slab suits most flat balconies and terraces, while a side-fixed system suits slabs where the top surface must stay clear. The required fixing size, spacing and glass thickness depend on the design loads for the location, so confirm these with a structural engineer or the system supplier rather than assuming a standard figure.
You should finish this step knowing which system you are using and having its installation instructions to hand.

Check your concrete and gather the right tools

Inspect the slab before you buy fixings, because anchors are only as reliable as the concrete holding them. Look for cracks, crumbling edges, spalling, exposed reinforcement or damp damage. Weak or damaged concrete can cause anchors to fail, so get a professional opinion if you have any doubts.
Check these points on the slab:

  • Edge distance: anchors placed too close to an edge can break out the concrete. Follow the minimum distances given by the anchor and system manufacturer.
  • Slab thickness and condition: there must be enough depth for the anchor type you plan to use.
  • Surface level: the fixing area should be flat, or you will need packers or levelling compound.
  • Waterproofing and finishes: on balconies, consider how membranes or screeds sit around the fixings and avoid creating a path for water.

Then gather your tools and materials:

  • Hammer drill with masonry or SDS bits (a core drill for core-drilled spigots)
  • Spirit level and laser level
  • Tape measure, marker and string line
  • Anchor bolts or chemical anchors specified for your system
  • Base channel or spigots, setting blocks, packers and wedges
  • Glass lifting equipment such as suction lifters, plus gloves and eye protection
  • Grout or sealant if your system requires it

Use the anchors specified for your system rather than substituting what you have in the garage. Your checkpoint here is a sound, dry, level slab and every item on the list laid out before drilling begins.

Drill and install anchors into the slab

Mark out the fixing positions accurately, as errors here are hard to correct once holes are drilled. Set out a straight line along the slab, mark each anchor or spigot position from your system drawing, and check that the spacing suits your panel widths. Where you are fixing a base channel, place the channel on the line and mark through its pre-drilled holes.
Follow these steps for each anchor:

  1. Drill to the diameter and depth stated by the anchor manufacturer, holding the drill square to the slab.
  2. Clean the hole thoroughly with a brush and blower. Dust left in the hole weakens both mechanical and chemical anchors.
  3. Install the anchor: tap in and tighten a mechanical anchor, or inject resin and set the stud for a chemical anchor.
  4. Allow chemical anchors to cure for the full time stated before applying any load or torque.

For core-drilled spigots, use a core drill to cut the holes to the specified diameter and depth, clear the slurry and debris, and keep the holes plumb so the spigots stand vertically. Be careful to avoid cutting reinforcement or hitting services, and use a scanner where you are unsure what lies within the slab.
When this step is done, anchors should sit firm, at the correct height and in line, with no spinning or movement when checked by hand.

Fit base shoes or spigots and set the glass

Fix the base channel or spigots to the anchors, keeping everything level and aligned before you add glass. Tighten fixings gradually and check level as you go, using packers to correct small variations in the slab rather than forcing the channel to follow it.
Setting the glass is a job for at least two people, as toughened glass panels are heavy and unforgiving at the edges. Use suction lifters and wear gloves and eye protection.

  1. Check each panel for chips or damage before lifting. Damaged edges on toughened glass are a risk and the panel should not be used.
  2. Lower the panel into the channel or between the spigot clamps, making sure the glass never rests directly on metal or concrete. Use the setting blocks supplied with your system.
  3. Plumb the panel with a spirit level and hold it in position with temporary wedges.
  4. Repeat for each panel, checking gaps and alignment against the run as you go.

Express Toughening manufactures made-to-measure glass balustrade panels, so panel sizes can be matched to your fixing layout and the slab dimensions. Once every panel stands plumb and evenly spaced, the structure is ready to be locked off.

Lock off, grout and check the finish

Secure the glass in position, then confirm everything is firm before removing any temporary support. In a base channel system, this usually means fitting wedges or a glazing gasket system, or filling the channel with a non-shrink grout where the system calls for it. For spigot systems, you tighten the clamp bolts to the torque stated by the manufacturer, and for core-drilled spigots you fill the holes with the specified grout or resin.
Follow these steps:

  1. Fix the glass using the locking method your system specifies, whether wedges, gaskets or grout.
  2. If grouting, mix the product strictly according to the instructions and fill the channel or hole fully, avoiding voids.
  3. Allow the grout to cure for the full time before removing wedges or applying load.
  4. Fit cover plates or trims to hide the fixings and protect them from water.
  5. If your design includes a handrail, fit it as the system instructions describe, as it can form part of the structural arrangement.

Finish by checking the whole run. Glass should be vertical, gaps even, fixings tight and no panel should move when pressed. Make sure there are no sharp edges exposed and no standing water pooling around the base on outdoor installations.

Fix common concrete fixing problems

Most issues trace back to the slab or to preparation, and many can be corrected before the balustrade is put into use. If something does not look or feel right, stop and seek professional advice rather than working around it.

Anchors spin or pull out

This usually means an oversized or dusty hole, weak concrete or the wrong anchor. Do not simply tighten harder. Remove the anchor, assess the concrete and reinstall using the correct anchor, or move the position if the concrete is damaged.

Concrete cracks or breaks out near the edge

This points to inadequate edge distance or overtightening. Cracked concrete around a fixing is a structural concern, so have it assessed before proceeding.

Base channel will not sit level

Use packers beneath the channel and check the slab surface. Large variations may need a levelling compound applied before the channel is fixed.

Water ingress around the base

Check that cover trims and sealants are correctly fitted and that falls on the slab direct water away from the fixings. On balconies, involve whoever installed the waterproofing so the fixings do not compromise it.

Glass looks out of plumb or panels do not align

Re-check the level of the channel or spigots and adjust with wedges before the grout sets. If the problem is a measuring error, panels may need to be remade to suit.

Explore Glass Balustrade Options with Express Glass Warehouse

Fixing a balustrade to concrete is straightforward when the fixing method, slab condition and glass specification are matched properly from the start. If you are planning a balcony, terrace, staircase or landing, Express Glass Warehouse can help you source the glass for the job.

  • Made-to-measure toughened and toughened laminated panels in thicknesses from 6mm to 21mm, for indoor and outdoor use
  • Complete balustrade systems including posts, clamps, handrails and fixings
  • A choice of glass types, including extra-clear low-iron, clear, tinted and satin, in rectangular, raked and parallelogram shapes

Browse the full glass balustrades range to compare options, or get in touch to discuss your project and panel sizes.

Related Articles

Certificates & Partners

What Our Customers Say

Andrew Cooke

Superb customer service from the Express Toughening team – when I made a mistake on my order online, they dealt with the issue quickly organising partial refund immediately. My order arrived quickly and their courier messaged me before delivery to check I was in. Quality product at the best price I found online.

Rated 5 out of 5
Kiron Kular

A massive Thankyou to Helen from Express Toughening for being so patient, co-operative and helpful with my orders. She resolved a re-make without any fuss and in an extremely timely manner. If you want glass – go to Express Toughening and ask for Helen!

Rated 5 out of 5
Andy Beviere

Extremely easy company to deal with, glass ordered weeks ago and asked for a specific delivery date due to glass testing and no one being onsite. Delivered on time and when asked for other types glass stated they couldn’t help but recommended an equally helpful company!!

Wouldn’t hesitate to use again.

Rated 5 out of 5
Brian White

I’ve used Express Toughening twice now and have been very impressed with the glass they have supplied and also the helpfulness of the staff. The first job was a couple of years ago when they supplied me with a 6mm satin frosted toughened glass door for our shower room. From my measurements they supplied a fabulous door which had the hinge and lock holes cut out and also took into account the out of square measurement of the door frame. It fitted a treat and is stunning to look at.

More recently (late last year) they supplied me with painted toughened glass splash backs (7 items altogether in 6mm glass with the biggest being 2.1 metres long), all cut to my sizes and with numerous switch and socket cut-outs. My local glass supplier said they could not cut out the close together sockets and switches, but Express did and got it spot on!

As with the glass door, the splash backs were delivered to me by Expresses’ own transport and without any problems and quality issues.

After the scary bit of fitting them all the result is faultless and stunning. Thanks go to Alex who helped me with the ordering process and technical aspects of glass splash backs.

Rated 5 out of 5
David Convery

4mm toughened glass for greenhouse. Although slightly dubious about ordering from a company I’ve never heard of and not local (300mile away) I’m so glad I took the plunge. A great customer service from Helen and the team from start to finish, clearly there was nothing for me to worry about.

Their website is easy to use and made ordering online a doddle and for those shapes, they don’t have on their website a quick email and rough diagram sorted any issues there. All glass arrived on time well packed and with no breakages.

It’s a company I wouldn’t hesitate to use again and I’d definitely recommend it to others who need quality glass cut to size.

Rated 5 out of 5
Tony Fields

Excellent product.
Exactly what it says on the tin.
Brilliant, friendly service from Helen.
Definitely recommended.
(And we’re on the Scottish border)

Rated 5 out of 5
Tony Owen

Fantastic service, fantastic prices and fantastic products – I could not recommend Express Toughening highly enough – I got an immediate response to my request for a quotation, and Helen was so helpful in answering my questions. Order placement was easy and everything arrived exactly on time and as promised. I won’t look anywhere else for my next order – great prices (way cheaper than other quotes) and great service!

Thank you!

Rated 5 out of 5
Sam Richardson

We have been using Express toughening for a number of years, mainly for glass screens and Toughened Glass for balustrade. The company are always reliable, deliveries always on time and friendly helpful service.

Rated 5 out of 5
Posted on Google Google
Nurul Ahmed
15 September 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
I ordered a table top protector from Express Toughening Ltd and I couldn’t be happier! Ridwan Nuruz provided exceptional, professional service from design right through to collection. A simple ikea sideboard now looks really classy and the top is super protected with toughened glass. So happy!
Posted on Google Google
Test
2 September 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great helpful team, service is excellent, product quality excellent, Delivery excellent. Will use again. Website is easy to order custom cuts. Don't hesitate, use this company
Posted on Google Google
Laura sabogal
15 August 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Express Toughening have been brilliant. Michael helped with my queries - cutting glass for my shower screen, he was quick to respond and just so helpful. They also offered the best price. I would definitely recommend!
Posted on Google Google
Alec parker-quaife
7 August 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Excellent experience Michael was extremely helpful and knowledgeable
Posted on Google Google
James Crispin
10 July 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great customer service. There was a problem with some of the glass table tops we ordered and it was sorted out immediately without any complaints or issues. Quality of glass is great. Can't fault the company and highly recommend them.
Posted on Google Google
Kevin costello
1 July 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Brilliant service. Spoke to Sean on a Thursday at 16:50 and had a quote back and order placed the same evening. Some panes were cracked when delivered but they were immediately remade and sent out. Good price and the service is miles ahead of other glass suppliers I've previously used.
Posted on Google Google
Admin CPA
9 June 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
⭐⭐⭐⭐⭐ Exceptional Service Thanks to Ghazal! I recently ordered a shower door and panel from Glass Toughening and had an outstanding experience, largely thanks to Ghazal Mubaied. From the very beginning, Ghazal was incredibly professional, responsive, and helpful, making the entire process smooth and stress-free. Her excellent communication and willingness to assist truly made a difference. While there was a slight delay in delivery, Ghazal’s proactive updates and dedication to ensuring customer satisfaction made it absolutely fine. Her professionalism and kindness turned what could have been a minor inconvenience into a non-issue. I highly recommend this company, also the prices are really good, especially if you have the pleasure of placing an order, ask for Ghazal. Their service quality is great, and having such a supportive team member like her makes all the difference. Thank you!
Posted on Google Google
Jemma Wisdom
5 June 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Brilliant service. Ghazal, was our contact and they guided us through the measuring and order process. We had a complicated order and they were brilliant. The bespoke screen was half the price of other services out there and it was delivered quickly, in perfect condition. Thank you Ghazal!
Posted on Google Google
Rob Fry
26 May 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Unbeatable on - price, quality, customer service and delivery. Is there anything more to say? 5 or maybe even 6 stars!
Posted on Google Google
Evaldas tuckus
20 May 2025
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great service, and specially Thanks to Ridwan Nuruz for his customer service.