How Do You Prevent Water Leaks Around a Frameless Glass Shower Screen?
A frameless glass shower screen looks clean and open, but without a frame to hide the joins, every gap shows and every weak seal can let water through. The good news is that most leaks come from a handful of predictable problems, and you can fix them yourself with basic tools. This guide shows you how to prevent shower screen leaks by checking alignment, sealing joints properly, fitting the right door seals and testing the finished installation.
It is worth being realistic from the start: a frameless shower screen can never be guaranteed completely watertight, because the door is not sealed in the way a framed enclosure is. The aim is to keep water where it belongs under normal use. You will need a spirit level, a tape measure, masking tape, a sealant gun, neutral-cure sanitary silicone, isopropyl alcohol or a suitable cleaner, lint-free cloths, a plastic sealant smoothing tool and a utility knife.
Check your walls, tray and screen alignment first
Check alignment before you reach for the silicone, because sealant cannot fix a screen that is out of plumb. Walls are rarely perfectly vertical and trays can settle or sit slightly out of level, so a gap that looks small at the bottom can become a wide, leaking channel by the top. If a toughened panel was ordered to measurements taken before tiling or before the tray was fitted, tolerances can be off, which is why shower glass should always be measured after tiles, trays and flooring are finished.
- Hold a spirit level against each wall where the glass will meet it and note any lean.
- Check the shower tray is level front to back and side to side.
- Offer up the glass panel, dry, with the correct temporary packing underneath, and look for uneven gaps along the wall and tray edges.
- Check that the panel itself sits plumb, and that hinges, brackets or channels are fixed to a solid backing rather than hollow board.
You should see a consistent, narrow and even gap along each joint, with the door swinging freely and closing evenly against its stop. Toughened glass cannot be cut, ground or drilled after it has been toughened, so a panel that is significantly the wrong size cannot be trimmed on site. If the gaps are wider than your sealant can safely bridge, speak to a professional before proceeding. Never force glass into position or let a toughened edge rest directly on a hard surface such as the tray or concrete, as edge impact can cause breakage.
Prepare and clean every joint before sealing
Clean and dry every joint thoroughly, because silicone only bonds well to surfaces that are free from dust, soap residue, grease and moisture. Most failed seals are not caused by poor silicone but by poor preparation, so give this step real attention.
- Remove any old sealant completely with a utility knife or sealant remover. Leftover silicone prevents new sealant from bonding.
- Wipe the glass edges, wall tiles and tray rim with isopropyl alcohol or a suitable cleaner and a lint-free cloth.
- Allow every surface to dry fully. Silicone applied to damp surfaces will not adhere properly.
- Apply masking tape in straight lines about 3 to 4 mm on either side of each joint to create a crisp sealant line and protect the tiles.
After this step, all joints should be bare, spotless and dry, with tape marking out a neat channel. If you cannot get the surfaces dry, wait until you can, as a rushed seal is the most common reason leaks return within weeks.
Apply silicone sealant to glass-to-wall and tray joints
Apply a continuous bead of neutral-cure sanitary silicone along the glass-to-wall joints and the glass-to-tray joint. Choose a sealant labelled for sanitary use with mould resistance, and avoid acetic (vinegar-smelling) types if your fittings or any natural stone are sensitive to them. Check the manufacturer’s guidance for compatibility with glass and your fittings.
Run the bead
- Cut the nozzle at a 45-degree angle to match the width of the joint.
- Starting at one end, apply steady pressure and move at a constant speed so the bead stays continuous, with no gaps or air pockets.
- Seal the outside face of the glass-to-tray joint as well as the inside where the design allows, as this helps prevent water tracking underneath.
Tool the joint
Smooth the bead straight away with a plastic smoothing tool, pressing the silicone gently into the joint so it makes full contact with both surfaces. Remove the masking tape while the sealant is still wet, pulling it away at an angle for a clean edge. You should now have a smooth, slightly concave line of silicone with no thin spots. If you see pinholes or gaps, add a little more silicone and re-tool immediately, rather than trying to patch it after it skins over.
Fit door seals, strips and magnetic gaps correctly
Fit the right seals to the moving parts of the screen, because the door edge is where frameless screens most often leak. Silicone handles the fixed joints, but the gap around a hinged door needs a flexible seal that stays in contact as the door opens and closes. A range of glass fittings including seals and hardware is available to suit different panel thicknesses, so check that the strip you buy matches your glass.
- Vertical door seal strips: fit along the hinge side or closing edge where the door meets a fixed panel or wall, to close the vertical gap.
- Bottom drip seals: fit along the base of the door with the fin angled so water runs back into the tray.
- Magnetic seals: use on door-to-panel closures where the two seals attract and close the gap while still allowing the door to open freely.
Cut each strip slightly long, then trim to length so it sits snugly without dragging on the tray. Press it on firmly along the full edge, then close the door and check that it meets the seal evenly from top to bottom. Hinge adjustment matters here too. Glass doors need hinges rated for the weight of the panel, and Express Toughening’s installation guidance generally describes two hinges for shower doors, with three recommended for doors taller than 2 metres, subject to the hardware manufacturer’s load limits. A door that sags will never seal properly, however good the strip. Closing the door should feel smooth, and you should see no visible daylight or uneven gaps around the edges.
Cure, test and fix remaining shower screen leaks
Allow the silicone to cure fully before using the shower, following the manufacturer’s instructions, which commonly specify 24 hours or more depending on the product and bead thickness. Using the shower early is a common mistake that breaks the seal before it has formed.
- After the full curing time, run the shower for a few minutes with the door closed, directing the spray towards the joints.
- Check the floor outside the screen, the base of the door and the wall joints for any water escaping.
- Dry the exterior with a towel and then repeat the test with the shower head angled at the door gap to see how well the seals cope.
If you find a leak, trace where the water first escapes, as it often travels along the glass before dripping. Small gaps in the silicone can be fixed by cleaning, drying and adding a fresh bead over the area once the old bead is cut back. Dripping from the door bottom usually calls for a deeper drip seal or a slight hinge adjustment. Persistent leaks from the door gap itself often mean the shower head direction needs changing, or that a wider door seal is needed. Remember that some splashing at the door edge is normal on frameless designs.
Check your seals every few months and replace silicone showing mould, cracking or peeling, as ageing sealant is the usual cause of leaks returning years later. If you suspect the wall, tray or fixings are structurally unsound, or the glass is out of alignment, call a qualified installer rather than relying on sealant alone.
Explore Bespoke Glass Shower Screens with Express Glass Warehouse
The best protection against leaks starts with glass that fits your bathroom properly. Express Glass Warehouse supplies bespoke, UK-made toughened glass panels made to your measurements, so gaps stay narrow and easier to seal. Browse the full range of glass shower screens to find a design for your space.
- Frameless shower screens, shower doors and bath screens made to your dimensions, with polished edges
- Glass options including extra-clear low-iron, clear, grey-tinted, bronze-tinted and satin toughened glass
- Matching fittings, hinges and seals to complete your installation, plus guidance on toughened glass specifications
Ready to start your project? Explore the shower screen collection, enquire about bespoke sizes, or find the right fittings and seals to keep your frameless screen working well for years to come.
Related Articles
- What Is the Difference Between Frameless and Post-Supported Glass Balustrades?
- Can You Replace a Shower Screen Without Replacing the Shower Tray?
- Are Bespoke Glass Shower Screens Suitable for Small Bathrooms?
- How do glass partitions compare to traditional walls?
- Why is toughened glass used in home renovations?




